XHH Wire
Specifications
| Property | Value |
|---|---|
| Full name | Cross-linked polyethylene High Heat-resistant |
| Insulation material | Cross-linked polyethylene (XLPE) |
| Outer covering | None |
| Temperature rating (dry) | 90°C (194°F) |
| Voltage rating | 600V |
| Approved locations | Dry only |
Advantages and limitations
XHH wire ampacity chart
Amps for XHH by size from NEC 2023 Table 310.16. Most circuits up to 100A are sized from the 60° or 75° column; which one is explained below the chart.
| Size | Copper | Aluminum | ||||
|---|---|---|---|---|---|---|
| 60° | 75° | 90° | 60° | 75° | 90° | |
| 14 | 15 | 20* | 25* | - | - | - |
| 12 | 20 | 25* | 30* | 15 | 20* | 25* |
| 10 | 30 | 35* | 40* | 25 | 30* | 35* |
| 8 | 40 | 50 | 55 | 35 | 40 | 45 |
| 6 | 55 | 65 | 75 | 40 | 50 | 55 |
| 4 | 70 | 85 | 95 | 55 | 65 | 75 |
| 3 | 85 | 100 | 115 | 65 | 75 | 85 |
| 2 | 95 | 115 | 130 | 75 | 90 | 100 |
| 1 | 110 | 130 | 145 | 85 | 100 | 115 |
| 1/0 | 125 | 150 | 170 | 100 | 120 | 135 |
| 2/0 | 145 | 175 | 195 | 115 | 135 | 150 |
| 3/0 | 165 | 200 | 225 | 130 | 155 | 175 |
| 4/0 | 195 | 230 | 260 | 150 | 180 | 205 |
| 250k | 215 | 255 | 290 | 170 | 205 | 230 |
| 300k | 240 | 285 | 320 | 195 | 230 | 260 |
| 350k | 260 | 310 | 350 | 210 | 250 | 280 |
| 400k | 280 | 335 | 380 | 225 | 270 | 305 |
| 500k | 320 | 380 | 430 | 260 | 310 | 350 |
* 240.4(D) limits the breaker on small conductors, whatever the column says: 14 AWG copper 15A, 12 AWG copper 20A, 10 AWG copper 30A, 12 AWG aluminum 15A, 10 AWG aluminum 25A.
XHH is rated 90°C dry, so it can use the columns of NEC 2023 Table 310.16 up to 90°C. The column you actually size with is set by the terminations, per 110.14(C): terminations on circuits of 100A or less, or marked for 14 AWG through 1 AWG, use the 60°C column unless the equipment is listed and marked for 75°C; terminations on larger circuits and conductors use 75°C. The 90°C column is the starting point for heat and bundling derating, not a breaker size.
When to use XHH wire
Dry locations where 90C rating needed. XHHW/XHHW-2 preferred when wet rating also needed.
Common applications for XHH:
- Specialized applications - XHH is used where its specific temperature and environment ratings are required
- See manufacturer specifications for approved installation methods
NEC code references for XHH
The NEC defines wire insulation types in Table 310.4(1) (formerly Table 310.104(A)). Key sections that apply:
- Table 310.4(1) - lists XHH with its temperature rating, insulation material, and approved locations
- Table 310.16 - ampacity values for conductors in raceway, cable, or earth (the values shown in our ampacity table above)
- Section 110.14(C) - termination temperature limits that determine real-world usable ampacity
- Section 310.15(C)(1) - adjustment factors for more than 3 current-carrying conductors in a raceway
Frequently asked questions about XHH wire
Where can I use XHH wire?
XHH is approved for use in dry only per NEC Table 310.4(1). It has a dry temperature rating of 90°C. Always verify that your specific installation meets the approved location requirements.
What is the temperature rating of XHH?
XHH is rated 90°C in dry locations. The ampacity values in NEC Table 310.16 use the 90°C column for conductors rated at or above 90°C, but actual usable ampacity is limited by the termination temperature (typically 75°C per 110.14(C)).
Other wire insulation types
NEC 2023 references verified February 2026 · Report a mistake