Connecticut Electrical Code & NEC Adoption
This guide covers everything you need to know about electrical code in Connecticut, including the current NEC edition (2020), wire sizing requirements, GFCI rules, electrician licensing, permit costs, and city-specific regulations. Connecticut scores 82/100 on WireRef's compliance scale, placing it in the moderate tier for code enforcement and safety oversight.
How Connecticut scores on electrical code compliance
WireRef rates each state's electrical code environment on a 0-100 scale based on four factors: NEC edition recency, licensing requirements, permit enforcement, and active state amendments. Connecticut scores 82/100, rated Moderate.
This score is for informational purposes only. A lower score does not mean electrical work in the state is unsafe - many local jurisdictions enforce strict standards independently of statewide policy.
Wire sizing requirements in Connecticut
The core ampacity values in NEC Table 310.16 have been unchanged since NEC 2017. Whether your Connecticut jurisdiction uses NEC 2017, 2020, 2023, or 2026, the wire sizing for residential circuits is identical. The table below covers the most common residential circuits:
| Circuit | Wire (Cu) | Breaker | Insulation |
|---|---|---|---|
| Kitchen 20A outlet Required for all kitchen receptacle circuits per NEC 210.11(C)(1) | 12 AWG | 20A | NM-B (Romex) |
| Bathroom 20A outlet Dedicated 20A circuit required per NEC 210.11(C)(3) | 12 AWG | 20A | NM-B (Romex) |
| General lighting 15A Standard for bedroom, living room, hallway lighting circuits | 14 AWG | 15A | NM-B (Romex) |
| Electric dryer 240V 10/3 NM-B for cable; 10 AWG THHN in conduit | 10 AWG | 30A | NM-B or THHN |
| Electric range 240V 6/3 NM-B for cable run; dedicated circuit required | 6 AWG | 50A | NM-B or THHN |
| EV charger (48A) 48A continuous load x 1.25 = 60A breaker minimum | 6 AWG | 60A | THHN in conduit |
| Central A/C (3-5 ton) Sized per unit nameplate MCA and MOCP values | 10-6 AWG | 30-50A | THHN |
| 200A dwelling service 2/0 copper or 4/0 aluminum per Table 310.15(B)(7) for dwelling services | 2/0 AWG | 200A | USE-2 or THHN |
For long wire runs in Connecticut (over 50 feet), voltage drop becomes the limiting factor before ampacity. Use our voltage drop calculator to verify your wire size keeps voltage drop under 3% for branch circuits or 5% total (feeder + branch).
GFCI requirements in Connecticut
Under NEC 2020 (enforced in Connecticut), GFCI was expanded to include basements (finished and unfinished) and laundry areas. However, kitchen GFCI is limited to countertop outlets within 6 feet of a sink - the refrigerator outlet is typically exempt.
| Location | GFCI requirement |
|---|---|
| Kitchen | Kitchen countertop receptacles within 6 feet of the sink require GFCI. Wall receptacles behind the refrigerator are usually exempt. Section 210.8(A)(6). |
| Bathroom | All bathroom receptacles require GFCI. Section 210.8(A)(1). |
| Outdoor | All outdoor receptacles require GFCI. In-use covers are required at grade level. Section 210.8(A)(3). |
| Garage | All garage receptacles require GFCI. Section 210.8(A)(2). |
| Basement | All basement receptacles require GFCI - expanded in 2020 to include finished basements. Section 210.8(A)(5). |
| Laundry | Laundry area receptacles within 6 feet of a sink require GFCI. Section 210.8(A)(10). |
See detailed GFCI rules by room: Kitchen · Bathroom · Garage · Outdoor · Basement · Laundry · Bedroom · Pool & Spa
Key differences: NEC 2020 vs NEC 2023
Connecticut currently enforces NEC 2020. Here are the major differences between your state's code and the latest NEC 2023 that may affect your project:
| Change | What it means |
|---|---|
| GFCI Requirements Expansion | Before: Kitchen GFCI required only for countertop receptacles (6-ft rule from sink) Now: ALL kitchen receptacles must be GFCI protected, plus hardwired appliances per 210.8(D) |
| General Lighting Loads Table Renumbering | Before: Table 220.12: Office = 1.5 VA/sqft (multiply by 1.25 for continuous) Now: Table 220.42(A): Office = 2.0 VA/sqft (already includes 1.25) |
Even though Connecticut enforces NEC 2020, your local inspector may require compliance with newer rules for new work. Always confirm with your local AHJ before starting a project.
Electrician licensing & permits in Connecticut
Connecticut requires electricians to be licensed. The primary license is the Electrical Contractor License, administered by the Connecticut Dept. of Consumer Protection - Electrical Licensing. Visit the Connecticut Dept. of Consumer Protection - Electrical Licensing website for application requirements and fees. Homeowners are generally exempt from licensing requirements when performing electrical work on their own primary residence - but permits and inspections are still required.
Verify a license: Check whether an electrician is properly licensed in Connecticut using the official license verification portal. Always verify before hiring.
Permits: Electrical permits are required for most new circuits, panel upgrades, and service changes. Homeowners may pull permits for their own primary residence in most jurisdictions.
Typical permit costs: Residential electrical permits in Connecticut generally range from $50-$200 depending on the scope of work and jurisdiction.
Permit costs are approximate and vary by jurisdiction. Contact your local building department for exact fees. Costs shown are for residential electrical permits and may not reflect commercial rates.
Common electrical projects that require a permit in most Connecticut jurisdictions:
- New circuits - adding any new branch circuit to the panel
- Panel upgrades - replacing or upsizing the main electrical panel
- Service changes - upgrading from 100A to 200A service
- EV charger installation - new 240V circuit for Level 2 charging
- Hot tub or pool wiring - Article 680 requirements apply
- Detached structure wiring - garage, shed, or ADU subpanel
Work that typically does not require a permit includes replacing switches, outlets, and light fixtures on existing circuits (no new wiring). However, rules vary - when in doubt, call your local Connecticut building department before starting.
License types in Connecticut
| License Type | Experience | Exam | Details |
|---|---|---|---|
| Journeyman Electrician (E-2) | See requirements | Yes | N/A |
| Electrical Contractor (E-1) | Journeyman + experience | Yes | Journeyman + experience |
Continuing education in Connecticut
Connecticut requires 4 hours of continuing education annually for license renewal. 4 hours annually. Must be completed by June 30. NEC code book required for class.
Homeowner exemption: Yes. Homeowners in Connecticut may perform electrical work on their own primary residence. Permits and inspections are still required.
Major cities: building departments & local codes
While Connecticut's statewide code provides the baseline, individual cities may have additional requirements, different permit fees, or local amendments. Below are the building department contacts for Connecticut's largest cities.
| City | Building Department | Notes |
|---|---|---|
| Hartford | Licenses and Inspections | Follows state NEC adoption |
| New Haven | Building Department | Follows state NEC adoption |
| Stamford | Building Department | Follows state NEC adoption |
City-specific information last verified Apr 2026. Contact the building department directly for current fees and requirements. WireRef is not affiliated with any municipal building department.
EV charger permit requirements in Connecticut
Most jurisdictions in Connecticut require an electrical permit for Level 2 EV charger installation. A Level 2 charger typically requires a dedicated 240V circuit with a 50A or 60A breaker and 6 AWG copper wire (for a 48A charger at continuous load).
| Spec | Requirement |
|---|---|
| Typical circuit | 240V, 50A or 60A breaker, 6 AWG copper THHN |
| Permit required | Yes, in most jurisdictions |
| Continuous load rule | 48A charger x 1.25 = 60A breaker (NEC 210.20) |
| GFCI/disconnect | Disconnect within sight of charger per NEC 625. GFCI protection per NEC 625.54 (outdoor) or manufacturer requirements |
As an Amazon Associate we earn from qualifying purchases.
See our complete EV charger wiring guide for detailed installation requirements. For state incentives and rebates, check the DSIRE database for Connecticut-specific programs.
Frequently asked questions: Connecticut electrical code
What NEC edition does Connecticut currently use?
Connecticut currently enforces NEC 2020. It became effective on October 01, 2022. This determines the baseline electrical safety requirements for all new electrical work in the state. Local jurisdictions may adopt more recent editions or add amendments.
Do I need an electrician license to do electrical work in Connecticut?
Yes - Connecticut requires a Electrical Contractor License for professional electrical work through the Connecticut Dept. of Consumer Protection - Electrical Licensing. However, homeowners are generally exempt when working on their own primary residence.
Do I need a permit for electrical work in Connecticut?
Yes - most electrical work in Connecticut requires a permit, including new circuits, panel upgrades, and service changes. Typical residential permit costs range from $50-$200. Homeowners can typically pull permits for their own residence.
How much does an electrical permit cost in Connecticut?
Residential electrical permits in Connecticut typically cost $50-$200 depending on the scope of work and specific jurisdiction. Costs vary significantly between cities - contact your local building department for exact fees.
What wire size do I need for a 20-amp kitchen circuit in Connecticut?
12 AWG copper is required for all 20-amp circuits regardless of which NEC edition Connecticut enforces - the ampacity tables in Table 310.16 have been unchanged since NEC 2017. Use 12/2 NM-B (Romex) for standard cable runs or 12 AWG THHN in conduit. See our kitchen wiring guide for complete requirements.
Does Connecticut require GFCI in the kitchen?
Under NEC 2020 (currently enforced in Connecticut), kitchen GFCI is required for countertop receptacles within 6 feet of the sink. The refrigerator outlet may be exempt. However, your local inspector may require broader GFCI coverage for new work.
Do I need a permit for an EV charger in Connecticut?
Yes - most Connecticut jurisdictions require an electrical permit for Level 2 EV charger installation since it involves a new 240V circuit. The typical installation requires a 60A breaker with 6 AWG copper wire for a 48A charger. See our EV charger wiring guide for complete specs.
How do I verify an electrician's license in Connecticut?
You can verify any electrician's license status through the official Connecticut license verification portal. Always verify before hiring an electrician for your project. Ask for the license number upfront and confirm it is active and in good standing.
How does Connecticut's electrical code compare to other states?
Connecticut scores 82/100 (Moderate) on WireRef's compliance scale. This is a moderate score - the state has licensing and permit requirements but may be one NEC cycle behind the latest edition.
Related guides
Compare Connecticut to other states
Head-to-head comparisons
All states
States are color-coded by NEC edition: 2023+ current, 2020 one cycle behind, older/local two+ cycles behind.
NEC 2023 references verified April 2026