Tankless Gas Water Heater: Wiring Requirements
Wiring a tankless gas water heater correctly means running 14 AWG copper on a 15-amp circuit. This guide covers the complete wiring requirements per NEC 2023, including wire gauge, breaker size, cable type, and installation specifics for your home. Whether you are hiring an electrician or planning the circuit yourself, the specifications below ensure your installation meets code.
Tankless Gas Water Heater electrical specifications
| Minimum wire gauge | 14 AWG copper |
| Breaker size | 15A single-pole |
| Voltage | 120V (120V single-phase) |
| Typical draw | 50-200W (0.4-1.7A) |
| Dedicated circuit | Can share with other outlets on the same circuit |
| Cable type | 14/2 NM-B (Romex) or 14 AWG THHN in conduit |
| GFCI required | Depends on location |
Circuit requirements for tankless gas water heater
Wire sizing: The minimum wire for a 15A circuit is 14 AWG copper. Use 14/2 NM-B cable (hot, neutral, ground) for standard residential runs in walls and attics. For wire runs over 50 feet, check voltage drop - you may need to upsize to 12 AWG to keep voltage drop under 3%.
Breaker sizing: A 15A breaker (single-pole, 120V) protects this circuit. The breaker must match or exceed the appliance nameplate rating but never exceed the wire capacity. 14 AWG copper is rated for well above 15A, providing adequate safety margin.
Installation notes
General wiring notes: Run the cable from the electrical panel to the appliance location using the most direct path through walls, floors, or attic space. Keep cable runs as short as practical to minimize voltage drop. Secure NM-B cable with staples within 12 inches of each box and every 4.5 feet along the run per NEC 334.30.
Receptacle type: Use standard NEMA 5-20R (T-slot) receptacles on 20A circuits, or NEMA 5-15R on 15A circuits. All receptacles must be tamper-resistant (TR) in new construction per NEC 406.12.
Safety and code requirements
GFCI: GFCI protection depends on the installation location. Kitchen, bathroom, garage, outdoor, basement, and laundry locations all require GFCI. See our GFCI guide by room to check whether your specific location requires it.
Ground wire: The equipment grounding conductor (green or bare wire) must be continuous from the panel to the appliance. For a 15A circuit, the minimum ground wire is 14 AWG copper per NEC Table 250.122. NM-B cable includes the correct ground wire size automatically.
Permits: Most jurisdictions require an electrical permit for adding a new circuit. The inspector will verify wire size, breaker rating, grounding, and GFCI protection. Check your state’s NEC adoption and call your local building department before starting work.
Typical installation
The typical installation involves running 14/2 NM-B cable from the electrical panel to the appliance location. Route the cable through wall cavities, floor joists, or attic space using the most direct path. Secure the cable with staples within 12 inches of each box and every 4.5 feet along the run. At the appliance end, connect to the appropriate receptacle or junction box.
Estimated materials cost
For a typical 50-75 foot run, expect to spend approximately $20-$56 on materials:
| 14/2 NM-B cable (50-75 ft) | $12-$41 |
| 15A breaker | $8-$15 |
| Estimated materials total | $20-$56 |
Material costs are approximate based on retail pricing as of Feb 2026. Actual costs depend on cable length, local pricing, and copper market conditions. Does not include labor, permits, or inspection fees.
Frequently asked questions
What size wire do I need for a tankless gas water heater?
14 AWG copper on a 15A breaker at 120V. This is the minimum per NEC Table 310.16. For runs over 50 feet, check voltage drop and consider upsizing to 12 AWG.
Does a tankless gas water heater need a dedicated circuit?
Not necessarily. A tankless gas water heater can typically share a general-purpose circuit with other outlets, as long as the total load does not exceed the breaker rating.
Does a tankless gas water heater need GFCI protection?
It depends on the location. If installed in a kitchen, bathroom, garage, outdoor area, basement, or laundry room, GFCI is required. Otherwise, GFCI is not specifically required but is always recommended near water.
Can I wire a tankless gas water heater myself?
In most states, homeowners can do their own electrical work on their primary residence with a permit and inspection. However, this is not a DIY task if you are unfamiliar with electrical work - improper wiring can cause fires or electrocution. Check your state licensing requirements and always get a permit.
Related guides
What to buy for this circuit
As an Amazon Associate we earn from qualifying purchases.
NEC 2023 references verified April 2026