RV Hookup (50A): Wiring Requirements
Wiring a rv hookup (50a) correctly means running 6 AWG copper on a dedicated 50-amp circuit with GFCI protection. This guide covers the complete wiring requirements per NEC 2023, including wire gauge, breaker size, cable type, and installation specifics for outdoor or exposed locations. Whether you are hiring an electrician or planning the circuit yourself, the specifications below ensure your installation meets code.
What usually triggers this search
You're adding electrical equipment outdoors and need weatherproof wiring that meets code for wet locations. Outdoor circuits have specific requirements for wiring methods, burial depth, GFCI protection, and enclosure ratings.
What goes wrong
Outdoor wiring degrades faster than any other residential installation. UV exposure, moisture, temperature cycling, and physical damage from landscaping all take a toll. The most common failure: using indoor-rated NM-B cable in an outdoor or underground application. NM-B has no UV or moisture protection and deteriorates within a few years outdoors. Underground runs need UF-B (direct burial) or individual conductors in conduit, with burial depth meeting Table 300.5. Outdoor receptacles need in-use covers (not just weatherproof covers) if the cord will be left plugged in, which is the case for most outdoor equipment.
What the inspector checks
- GFCI protection on all outdoor receptacles per 210.8(A)(3)
- Wiring methods rated for wet locations (UF-B, conductors in conduit, etc.)
- Burial depth per Table 300.5 for underground runs
- In-use covers on receptacles where equipment stays plugged in
Should you hire an electrician?
Adding an outdoor receptacle from an existing interior circuit is manageable for a handy homeowner if you understand weatherproof boxes and GFCI requirements. Underground runs require proper burial depth and conduit. Budget $200-500 for an electrician to run a new outdoor circuit.
RV Hookup (50A) electrical specifications
| Minimum wire gauge | 6 AWG copper |
| Breaker size | 50A single-pole |
| Voltage | 120/240V (120V single-phase) |
| Typical draw | 12,000-12,000W (10-15A) |
| Dedicated circuit | Yes - no other loads on this breaker |
| Cable type | 6/2 NM-B (Romex) or 6 AWG THHN in conduit |
| GFCI required | Yes - NEC 210.8(A) |
Circuit requirements for rv hookup (50a)
A rv hookup (50a) must have a dedicated circuit - no other appliances, outlets, or loads should share this breaker. This means running a new 6/2 NM-B cable from the electrical panel directly to the appliance location.
Wire sizing: The minimum wire for a 50A circuit is 6 AWG copper. Use 6/2 NM-B cable (hot, neutral, ground) for standard residential runs in walls and attics. For wire runs over 50 feet, check voltage drop - you may need to upsize to 4 AWG to keep voltage drop under 3%.
Breaker sizing: A 50A breaker (single-pole, 120V) protects this circuit. The breaker must match or exceed the appliance nameplate rating but never exceed the wire capacity. 6 AWG copper is rated for well above 50A, providing adequate safety margin.
Installation notes
Outdoor wiring rules: All outdoor receptacles require GFCI protection per NEC 210.8(A)(3). Receptacles accessible at grade level need weather-resistant, in-use covers (not just weatherproof covers). Underground cable must meet burial depth requirements - typically 24 inches for direct-burial UF-B cable or 18 inches for conduit.
Receptacle type: Use standard NEMA 5-20R (T-slot) receptacles on 20A circuits, or NEMA 5-15R on 15A circuits. All receptacles must be tamper-resistant (TR) in new construction per NEC 406.12.
Safety and code requirements
GFCI protection is required for this appliance location. Install GFCI protection at the breaker (GFCI breaker) or at the first receptacle in the circuit. See Outdoor GFCI requirements for the full NEC rules and edition-by-edition changes.
Ground wire: The equipment grounding conductor (green or bare wire) must be continuous from the panel to the appliance. For a 50A circuit, the minimum ground wire is 10 AWG copper per NEC Table 250.122. NM-B cable includes the correct ground wire size automatically.
Permits: Most jurisdictions require an electrical permit for adding a new circuit. The inspector will verify wire size, breaker rating, grounding, and GFCI protection. Check your state’s NEC adoption and call your local building department before starting work.
Typical installation
Outdoor wiring requires weather-rated components. The typical approach is to run NM-B cable inside the house to an exterior wall, transition to conduit (PVC or rigid) through the wall with a weather head or LB fitting, and extend to a weatherproof box at the appliance location. All underground runs must meet burial depth requirements. An in-use cover (not just a flip lid) is required for receptacles accessible at grade.
Estimated materials cost
For a typical 50-75 foot run, expect to spend approximately $164-$433 on materials:
| 6/2 NM-B cable (50-75 ft) | $114-$338 |
| 50A GFCI breaker | $50-$95 |
| Estimated materials total | $164-$433 |
Material costs are approximate based on retail pricing as of Feb 2026. Actual costs depend on cable length, local pricing, and copper market conditions. Does not include labor, permits, or inspection fees.
Frequently asked questions
What size wire do I need for a rv hookup (50a)?
6 AWG copper on a 50A breaker at 120/240V. This is the minimum per NEC Table 310.16. For runs over 50 feet, check voltage drop and consider upsizing to 4 AWG.
Does a rv hookup (50a) need a dedicated circuit?
Yes. A rv hookup (50a) requires its own dedicated circuit - no other outlets or appliances can share the breaker.
Does a rv hookup (50a) need GFCI protection?
Yes. NEC 210.8(A) requires GFCI protection for this appliance regardless of where it is installed. Install a GFCI breaker or GFCI-protected receptacle.
Can I wire a rv hookup (50a) myself?
In most states, homeowners can do their own electrical work on their primary residence with a permit and inspection. However, this is not a DIY task if you are unfamiliar with electrical work - improper wiring can cause fires or electrocution. Check your state licensing requirements and always get a permit.
Related guides
What to buy for this circuit
As an Amazon Associate we earn from qualifying purchases.
NEC 2023 references verified April 2026