Radon Mitigation Fan: Wiring Requirements
Wiring a radon mitigation fan correctly means running 14 AWG copper on a 15-amp circuit. This guide covers the complete wiring requirements per NEC 2023, including wire gauge, breaker size, cable type, and installation specifics for your HVAC system. Whether you are hiring an electrician or planning the circuit yourself, the specifications below ensure your installation meets code.
What usually triggers this search
Your heating or cooling equipment is being replaced and the new unit has different electrical requirements than the old one. HVAC circuits are always sized from the unit's nameplate, not from generic tables.
What goes wrong
HVAC wiring failures come from mismatching the circuit to the equipment. Every condenser, heat pump, and air handler has MCA (Minimum Circuit Ampacity) and MOP (Maximum Overcurrent Protection) on the nameplate. Ignoring these numbers causes two problems: undersized wire that causes voltage drop and premature compressor failure, or an oversized breaker that won't protect the equipment during a fault. The outdoor disconnect is another common failure point. It must be within sight of the equipment. Corrosion on outdoor disconnect terminals causes high-resistance connections that overheat.
What the inspector checks
- Wire and breaker match unit nameplate MCA and MOP
- Disconnect within sight of equipment and readily accessible
- Proper liquid-tight flexible conduit from disconnect to unit
- Equipment grounding conductor properly sized and connected
Should you hire an electrician?
HVAC electrical work is usually coordinated between the HVAC installer and an electrician. The circuit run and disconnect installation are electrical work. The connection to the unit is often done by the HVAC company. Budget $300-700 for circuit and disconnect depending on distance and wire size.
Radon Mitigation Fan electrical specifications
| Minimum wire gauge | 14 AWG copper |
| Breaker size | 15A single-pole |
| Voltage | 120V (120V single-phase) |
| Typical draw | 50-150W (0.4-1.2A) |
| Dedicated circuit | Can share with other outlets on the same circuit |
| Cable type | 14/2 NM-B (Romex) or 14 AWG THHN in conduit |
| GFCI required | Depends on location |
Circuit requirements for radon mitigation fan
Wire sizing: The minimum wire for a 15A circuit is 14 AWG copper. Use 14/2 NM-B cable (hot, neutral, ground) for standard residential runs in walls and attics. For wire runs over 50 feet, check voltage drop - you may need to upsize to 12 AWG to keep voltage drop under 3%.
Breaker sizing: A 15A breaker (single-pole, 120V) protects this circuit. The breaker must match or exceed the appliance nameplate rating but never exceed the wire capacity. 14 AWG copper is rated for well above 15A, providing adequate safety margin.
Installation notes
HVAC wiring notes: Air conditioning and heat pump circuits are sized from the unit nameplate - look for the MCA (minimum circuit ampacity) and MOCP (maximum overcurrent protection) values. The wire must handle the MCA, and the breaker must not exceed the MOCP. A disconnect switch within sight of the outdoor unit is required per NEC 440.14.
Receptacle type: Use standard NEMA 5-20R (T-slot) receptacles on 20A circuits, or NEMA 5-15R on 15A circuits. All receptacles must be tamper-resistant (TR) in new construction per NEC 406.12.
Safety and code requirements
GFCI: GFCI protection depends on the installation location. Kitchen, bathroom, garage, outdoor, basement, and laundry locations all require GFCI. See our GFCI guide by room to check whether your specific location requires it.
Ground wire: The equipment grounding conductor (green or bare wire) must be continuous from the panel to the appliance. For a 15A circuit, the minimum ground wire is 14 AWG copper per NEC Table 250.122. NM-B cable includes the correct ground wire size automatically.
Permits: Most jurisdictions require an electrical permit for adding a new circuit. The inspector will verify wire size, breaker rating, grounding, and GFCI protection. Check your state’s NEC adoption and call your local building department before starting work.
Typical installation
HVAC equipment wiring connects from a dedicated breaker in the main panel to a disconnect switch mounted within sight of the outdoor unit, then from the disconnect to the unit. The disconnect is typically a non-fused pull-out type mounted on the wall near the condenser. Use THHN wire in conduit for the outdoor portion. The indoor air handler connects via a separate low-voltage thermostat wire (typically 18/5 or 18/8).
Estimated materials cost
For a typical 50-75 foot run, expect to spend approximately $20-$56 on materials:
| 14/2 NM-B cable (50-75 ft) | $12-$41 |
| 15A breaker | $8-$15 |
| Estimated materials total | $20-$56 |
Material costs are approximate based on retail pricing as of Feb 2026. Actual costs depend on cable length, local pricing, and copper market conditions. Does not include labor, permits, or inspection fees.
Frequently asked questions
What size wire do I need for a radon mitigation fan?
14 AWG copper on a 15A breaker at 120V. This is the minimum per NEC Table 310.16. For runs over 50 feet, check voltage drop and consider upsizing to 12 AWG.
Does a radon mitigation fan need a dedicated circuit?
Not necessarily. A radon mitigation fan can typically share a general-purpose circuit with other outlets, as long as the total load does not exceed the breaker rating.
Does a radon mitigation fan need GFCI protection?
It depends on the location. If installed in a kitchen, bathroom, garage, outdoor area, basement, or laundry room, GFCI is required. Otherwise, GFCI is not specifically required but is always recommended near water.
Can I wire a radon mitigation fan myself?
In most states, homeowners can do their own electrical work on their primary residence with a permit and inspection. However, this is not a DIY task if you are unfamiliar with electrical work - improper wiring can cause fires or electrocution. Check your state licensing requirements and always get a permit.
Related guides
What to buy for this circuit
As an Amazon Associate we earn from qualifying purchases.
NEC 2023 references verified April 2026